Structural dependence of microwave dielectric properties of spinel structured Mg2(Ti1-xSnx)O4 solid solutions: Crystal structure refinement,Raman spectra study and complex chemical bond theory

Mg₂(Ti_1-xSn_x)O₄ (x?=?0–1) ceramics were prepared through conventional solid-state method. This paper focused on the dependence of microwave dielectric properties on crystal structural characteristics via crystal structure refinement, Raman spectra study and complex chemical bond theory. XRD spectrums delineated the phase information of a spinel structure, and structural characteristic of these compositions were achieved with the help of Rietveld refinements. Raman spectrums were used to depict the correlations between vibrational phonon modes and dielectric properties. The variation of permittivity is ascribed to the Mg₂(Ti_1-xSn_x)O₄ average bond covalency. The relationship among the B-site octahedral bond energy, tetrahedral bond energy and temperature coefficient are discussed by defining on the change rate of bond energy and the contribution rate of octahedral bond energy. The quality factor is affected by systematic total lattice energy, and the research of XPS patterns illustrated that oxygen vacancies can be effectively restrained in rich oxygen sintering process. Obviously, the microwave dielectric properties of Mg₂(Ti_1-xSn_x)O₄ compounds were obtained (${\epsilon }_r$= 12.18, $Q\times f$?=?170,130?GHz, ${\tau }_f$?=??53.1?ppm/°C, x?=?0.2).     

High birefringence photonic bandgap fiber with elliptical air holes

In this paper, we proposed a high birefringence photonic bandgap fiber (PBGF) with elliptical air holes in cladding and circular air hole in core. The forbidden gaps of the honeycomb structure are calculated when the circular air holes are deformed to the elliptical shape. And the birefringence of the PBGFs is investigated by using a full-vector finite element method (FEM) and the numerical results are presented.     

Charting of geoelectric potential signal dynamics via geometrical techniques and its possible relation to significant earthquakes in Western Greece

An exploratory data analysis (EDA) framework was developed in order to investigate the presence of possible correlations in the long-term geoelectric potential (LTGP) signal, prior to significant seismic events in Western Greece. Experimental data, which had been collected continuously within a 6-year period (1998–2003) at the earthquake signal-acquisition center of the University of Patras Seismological Laboratory (UPSL), were studied. The multidimensional scaling (MDS) technique was used to detect putative clustering tendencies in the ensemble of time-series (TS) segments that could indicate the existence of a possible correlation between the geoelectric signal structure and the impending seismic activity. The end result is a 2-dimensional point diagram with the geometry reflecting important signal characteristics, directly related with the underlying seismic events. In addition, the “appending technique”, a well-suited data analysis methodology was incorporated as a means of relating any other TS segment directly with the pre-computed, via the MDS, point diagram. Using the proposed EDA framework, we examined the presence of similar temporal patterns in the recorded geoelectric TS field, 10 days before the occurrence of the major earthquakes. The presented experimental results indicated clearly the validity of the introduced approach and, further, motivated the use of such advanced visualization schemes for charting precursor trends of significance seismicity.     

Silver nanocluster formation in silicate glass by single step ion-exchange

We report the formation of silver nanoclusters of average size ∼ 1.1 nm in a single step ion-exchanged silica glass. Silver clusters are formed in a glass during ion-exchange by fine-tuning the ion-exchange parameters such as salt composition, temperature and time. Such nanocluster formation during ion-exchange preserves the waveguiding properties of the ion-exchanged surface of the glass making them suitable for nonlinear waveguide device fabrication.     

Electrical properties and positron annihilation study of (Ba<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Ho<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>)TiO<Subscript>3</Subscript> ceramics

DC resistivity, dielectric constant, dielectric loss and positron annihilation spectra of (Ba_1−x Ho _x )TiO₃ ceramics have been measured as a function of holmium concentration x. It has been found that the DC resistivity of (Ba_1−x Ho _x )TiO₃ is strongly dependent on the Ho content: it decreases three orders of magnitude and reaches a minimum at x = 0.4%. Doping with 0.6% holmium increases the permittivity of BaTiO₃ by approximately three times (from ∼1,300 to ∼4,000), with only a slight increase in the corresponding dielectric loss. The local electron density and defect concentration estimated using positron annihilation technique conforms well to the features found in the dielectric and resistivity measurements. The results have been discussed in terms of a mixed compensation model.     

The influence of ply sequence and thermoelastic stress field on asymmetric delamination crack growth behavior of embedded elliptical delaminations in laminated FRP composites

The influence of ply lay up and the interaction of residual thermal stresses and mechanical loading on the interlaminar asymmetric embedded delamination crack growth behavior have been investigated. Two sets of full three-dimensional thermo-elastic finite element analyses have been performed for the interlaminar elliptical delaminations, which may be due to manufacturing defects or other reasons and are located symmetrically with respect to the midplane in a quasi-isotropic FRP composite laminate lay up. Depending upon the through-the-thickness location of the embedded elliptical delaminations, four different laminate configurations have been considered. Strain energy release rate (SERR) procedures have been employed to assess the delamination crack growth characteristics at the interfaces. It is found that the individual fracture modes exhibit asymmetric and non self-similar crack growth behavior along the delamination front depending upon the location of the interfacial delaminations; ply sequence and orientation and thermo-elastic anisotropy of the laminae.     

An efficient face segmentation algorithm based on binary partition tree

This paper presents an efficient face segmentation algorithm based on binary partition tree. Skin-like regions are first obtained by integrating the results of pixel classification and watershed segmentation. Facial features are extracted by the techniques of valley detection and entropic thresholding, and are used to refine the skin-like regions. In order to segment the facial regions from the skin-like regions, a novel region merging algorithm is proposed by considering the impact of the common border ratio between adjacent regions, and the binary partition tree is used to represent the whole region merging process. Then the facial likeness of each node in the binary partition tree is evaluated using a set of fuzzy membership functions devised for a number of facial primitives of geometrical, elliptical and facial features. Finally, an efficient algorithm of node selecting in the binary partition tree is proposed for the final face segmentation, which can exactly segment the faces without any underlying assumption. The performance of the proposed face segmentation algorithm is demonstrated by experimental results carried out on a variety of images in different scenarios.     

Thermoelastic evaluation of composite laminates using digital imaging processing

The study of the variation of the curvature of non-symmetric composite laminates with temperature provides a measure of the magnitude of the thermal stresses and the mechanical behavior of the material with temperature. In the present work, an experimental method based on the pioneer use of a digital camera and image processing method is proposed to perform such measurements. Taking advantage of the method and by comparing experimental and CLT, extended-CLT and FEM simulation results, an evaluation of the residual stresses is described and an approach providing more precise determination of the residual thermal stresses in non-symmetric laminates is proposed.     

High mobility,low voltage polymer transistor

We introduce a polymer transistor that operates with low supply voltage and yet has a field-effect mobility higher than the mobilities reported for low voltage polymer transistors. A simple plasma oxidation of the gate metal to form a thin (3.74 nm) top metal oxide layer in the gate metal is involved in the fabrication that acts as the gate dielectric. With ultrathin gate dielectrics, the variation in the dielectric thickness and the surface roughness scattering can severely limit the mobility attainable. The plasma oxidation under certain conditions produces a very smooth oxide surface, leading to the high mobility.